Cost to Build a Deck in Augusta, ME: The 2026 Numbers

Cost to build a deck in Augusta, ME: finished composite deck with black rail and stairs behind a cape

The cost to build a deck in Augusta, ME starts at $80 per square foot for an all pressure-treated build, turnkey with railing, and reaches $100 to $120 on larger or more complicated layouts.

Updated for 2026.

The most useful thing on this page is not the rate. It is the reason a small deck costs more per square foot than a big one, which is the opposite of what almost everybody assumes.

If you want the build itself rather than the budget, what goes into a deck is on its own page.

The Rates

Every deck budget in Augusta starts from these figures.

ScopeFigure
All pressure-treated, new build$80 per square foot
Larger or more complicated layouts, shapes, and tie-ins$100 to $120
Project floor, all pressure-treated$10,000
Project floor, composite decking with composite railing$15,000

Towns farther out, on camp roads, on ledge, or with tight urban staging carry up to 10% above those figures. Augusta itself sits at the base rate.

Each band is an average across hundreds of quotes rather than a bid for any particular deck.

Cost to Build a Deck in Augusta, ME by Size

Here is how the rates land on four common deck sizes.

DeckPressure treatedComposite
8x12 (96 sq ft)about $9,800 with stairs$15,000 floor
12x16 (192 sq ft)about $10,800$15,400
16x20 (320 sq ft)$25,600 to $32,000 if complex$28,000 and up
20x24 (480 sq ft)$38,400 to $48,000 if complex$42,000 and up

Look at the first two rows again. That is the whole point of this guide.

Pressure-treated deck by size, the starting figureThe first two sizes sit close together, and the second is twice the deck.
Pressure-treated deck by size, the starting figure
ItemValue
8x12$9,800
12x16$10,800
16x20$25,600
20x24$38,400

Averages across hundreds of quotes, not a bid. Complex layouts on the two larger sizes run to $32,000 and $48,000.

Small Decks Cost More Per Foot

Footings are close to a fixed cost. An 8x12 pressure-treated deck with stairs and six footings runs about $9,800.

Why a small deck costs more per foot
$9,800An 8x12 pressure-treated deckWith stairs and six footings
$1,000More for a 12x16Roughly, for twice the deck
One dayAdded for stagingOnce the deck rises past about 2 feet

A 12x16 costs roughly $1,000 more and delivers exactly twice the deck.

So going bigger is cheap per square foot, and shrinking a design almost never saves what people expect it to. If the budget is tight, the honest advice is usually to build the size you want and simplify the shape.

Height works the same way. Getting more than about 2 feet off the ground adds roughly one crew day for staging, and that day is the same on a 3-day build as on a 12-day one, so the percentage hit is far larger on a small deck.

What Moves the Number

  • Stairs, and how many runs. Each set of stairs is framing, treads, railing, and a landing.
  • Shape. Angles, curves, and multiple levels are all labor rather than material.
  • Height off the ground, past roughly 2 feet.
  • Whether usable footings already exist, which sometimes they do and often they do not at the right depth.
  • Tie-in to the house, and whether a ledger is even the right approach.
  • Railing choice. Aluminum, composite, and cable all price differently, and railing is a bigger share of a small deck than a large one.

One local line item worth knowing: Waterville and some southern Maine towns set the deck permit fee as a percentage of total project price. On a large deck that is real money and it should appear on the estimate rather than as a surprise.

Low two-level pressure-treated deck with wide steps on two sides behind a gray Cape in Augusta, Maine
Levels, steps and shape are labor more than lumber, so they move the price more than the boards do.

What a Deck Should Be Built To

The spec below is what separates a deck that lasts from one that gets rebuilt in fifteen years. Ask any bidder to confirm each line.

  • Footings to 4 feet, full frost depth. Helical piles on most jobs, because they go in clean and do not need the hole to stay open.
  • Joists 16 inches on center, and 12 inches under PVC, which spans differently and telegraphs a soft frame.
  • Joist tape on every joist. The fastener holes are where a frame rots first.
  • Hidden clips, face-screwed and plugged on PVC because PVC moves with temperature.
  • Flashing at the ledger, always. A ledger without flashing is the most common serious defect we find on an existing deck.
  • Trim so no end grain shows. End grain drinks water.

Three things nobody should accept: floating deck blocks, an unflashed ledger, and new decking laid over an old frame.

Framing, ledger connection, and guard requirements are set out in the residential code, and the ledger section is worth reading yourself before you sign anything.

The spec to confirm with any bidder
Line itemWhat to ask forWhy it matters
Footings4 feet, full frost depth, helical piles on most jobsThey go in clean and the hole never has to stay open
Joist spacing16 inches on center, 12 inches under PVCPVC spans differently and telegraphs a soft frame
Joist tapeOn every joistThe fastener holes are where a frame rots first
FasteningHidden clips, face-screwed and plugged on PVCPVC moves with temperature
LedgerFlashed, alwaysThe most common serious defect we find on an existing deck
TrimNo end grain showingEnd grain drinks water

Wood or Composite

Pressure treated is the cheapest way to get a deck and it needs maintenance you will actually have to do. By two decades it is done, and the tell is an owner who has already replaced individual dangerous boards.

Decking and railing, side by side
Lowest up frontPressure treated
  • The cheapest way to get a deck
  • Maintenance you will actually have to do
  • Done by about two decades
What we specifyComposite and PVC
  • Costs more up front
  • Almost nothing after
  • TimberTech and AZEK first
Sets the lookRailing
  • Where the look gets decided
  • Westbury aluminum by default
  • TimberTech Radiance Rail as the alternative

The composite project floor is $15,000, against $10,000 for pressure treated.

Composite and PVC cost more up front and almost nothing after. TimberTech and AZEK are what we specify first, with Deckorators mineral-based as an emerging option and Trex on request. Span and fastening requirements are published by the manufacturer.

Railing is where the look gets decided. Westbury aluminum is our default, with TimberTech Radiance Rail as the composite alternative.

The composite project floor is $15,000 rather than $10,000, which means composite rarely makes sense on a very small deck and usually makes sense on a large one.

Common Questions

Can you build on my existing footings?

Sometimes. Depth, condition, and spacing all matter, and the frame is what everything else depends on, so it is worth an honest answer rather than a hopeful one.

Do I need a permit for a deck in Augusta?

Generally yes for a structure attached to the house or above a height threshold. The city's code office decides, and we file the application.

How long does a deck take?

Three days to two weeks for most projects, driven by size, height, and stair count.

Why helical piles?

They reach full depth cleanly, they work in wet ground where a poured hole collapses, and they can go in when a poured footing would have to wait.

Three quick answers
Existing footingsSometimes usable. Depth, condition and spacing decide it.
The permitGenerally needed when the deck is attached or high. We file the application.
How long it takesThree days to two weeks for most projects.

Get a Real Number

Maine has no state licensing standard for deck builders, so the written scope is the protection. Ask for footing depth, joist spacing, joist tape, and the ledger detail in writing, plus a fixed price under Maine's home construction contract law.

What to get in writing

Brandon takes the calls at (207) 480-7700. Email [email protected], or book a free estimate.